Present RV has a POWERMAX Floor Mount Series Converter/Charger POWERMAX has six floor mount models available and PDI can supply lithium replacement converter/charger units for the models shown below. It’s the smart method to keep your RV battery charged and maintained Another great feature of this model is it built-in Charge Wizard 4-stage charging mechanism that significantly extends battery life. Present RV has a IOTA Floor Mount Series Converter/Charger IOTA has four floor mount models available and PDI can supply lithium replacement converter/charger units for the models shown below. The PD4645V can replace Parallax/Magnatek 6345, Parallax 7345, Parallax 8345, and WFCO 8945 converter sections. Present RV has a WFCO Wall Mount Series Converter/Charger WFCO has three wall mount models available and PDI can supply lithium replacement converter/charger units for the models shown below. With our large selection of RV power converters by Parallax Power Supply you wont have to worry with the lights dimming. Present RV has a WFCO Floor Mount Series Converter/Charger WFCO has several floor models and PDI can supply lithium replacement units for the models shown below. RV Power Converters helps keep your RV batteries charged and converting 12 volt power for your RV. Just used this converter on a 3 week trip in. These replacement sections allow you to easily remove your present lead/acid section and replace it with a lithium unit. I replaced my batteries with lithiums so I had to replace the charger also. Present RV has a Progressive Dynamics PD4000 Series Converter/Charger Note: Progressive Dynamics has two converter/charger replacement sections for the PD4000 series units. Present RV has a Progressive Dynamics PD9200 Series Converter/Charger Present RV has a Progressive Dynamics PD9100 Series Converter/Charger Depending on your knowledge of electricity you may want to consult a licensed electrician or RV technician for assistance. Once Converter/Charger Section mounting screw is removed, (mark the location & color) of the wires then disconnect five colored wires and slide out present Lead/Acid section and replace with the new Lithium Section reconnecting the wires to their proper location. Replacement requires removal of the front panel of your present Wall Mount unit to gain access to the Converter/Charger Section. The fourth photo on this page shows a typical Lithium Replacement Section for All Wall Mount units. WARNING! Disconnect all 120 VAC power before removing and replacing converter/charger section! You are here: Home / Converter Repair Parts & Accessories / Parallax 7300 Series Converter Replacement Fan. NOTE: Lithium Replacement Sections are only available for Progressive Dynamics and WFCO Wall Mount units. These Replacement Lithium Sections are available from our approved distributors. Updating to a Lithium Battery System requires the removal and replacement of the present slide out Lead/Acid Converter/Charger Section with one designed to charge Lithium Batteries. The unit also includes a 12-Volt DC Fuse Panel to supply 12-Volt power to all 12-Volt circuits. The Wall Mount units as their name implies are mounted in the RV interior wall or cabinet for easy accessibility and include a removable Converter/Charger Section, a 120 VAC Distribution Panel with a 30 or 50 Amp Main AC Circuit Breaker and several 120 VAC AC Branch Circuit Breakers. The new fuse block mounts in the exact same position, using the existing holes and supplied screws.WARNING! Do not replace your present Lead/Acid Converter/Charger or Converter/Charger Section with a Lithium Model with an Amp rating higher than the D.C Amp output rating of your present unit as your RV wiring is may not be capable of safely handling this extra current! The two additional 30 Amp fuses are provided for reverse polarity protection. With the new fuse block, all branch circuits are filtered with or without a battery (from the converter), to provide clean DC output to ALL of your DC appliances and accessories. Positions 7-9 are filtered but only if you have a battery installed. * If you look at the back of your existing DC fuse block, positions 1-6 are not filtered from the battery because they do not connect to the battery positive lug. Kits include the converter/charger, new DC fuse block, two 30 Amp fuses, AC pigtail, 6 AWG DC wires, and all hardware necessary to make the conversion. Output voltages are (13.2 VDC Float, 13.6 VDC Normal, and 14.4 VDC Boost) The multi-stage charge technology is built-in to the converter. For additional photos, check out our converter upgrade link. All kits have built-in 3 or 4-stage charging and 100% filtered DC output. Available in 35, 45 or 55 Amp models, Our upgrade kits are designed to replace Magnetek, B-W Manufacturing, Magnetek and Parallax 6300 or 7300 or 8300 Series lower converter-charger sections.
0 Comments
Leave a Reply. |